Phase composition,microstructure and thermophysical properties of the Srx(Zr0.9Y0.05Yb0.05)O1.95+x ceramics

Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8, 0.7) ceramics were prepared by solid state reaction sintering. The sintered Sr_1.0(Zr_0.9Y_0.05Yb_0.05)O_2.95 is a single-phase solid solution while the sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=0.9?0.7) are composites, and a significant grain growth inhibition is observed in the sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9). Rare-earth elements distribution in the bulk materials indicates that Yb and Y preferentially substitute Zr-sites in SrZrO₃, and the highest solubility of RE₂O₃ in pure SrZrO₃ is ～0.8 mol%. The sintered Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x have high thermal expansion coefficients up to ～11.0×10^?6 K^-1 (1200°C). Sr_0.8(Zr_0.9Y_0.05Yb_0.05)O_2.75 has the lowest thermal conductivity of 1.38 W·m^-1·K^-1 at 800°C. Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8) show no phase transition from 600 to 1400°C, whereas Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=0.9, 0.8) have excellent high-temperature phase stability over the whole investigated temperature range. Therefore, Sr_x(Zr_0.9Y_0.05Yb_0.05)O_1.95+x (x=1.0, 0.9, 0.8) are considered as promising TBCs materials that might be operated at higher temperatures compared to YSZ.     

High energy-storage performance of lead-free AgNbO3 antiferroelectric ceramics fabricated via a facile approach

AgNbO₃ lead free AFE ceramics are considered as one of the promising alternatives to energy storage applications. In the majority of studies concerning the preparation of AgNbO₃ AFE ceramics, an oxygen atmosphere is required to achieve high performance, increasing the complexity of the fabrication process. Herein, a facile approach to preparing AgNbO₃ ceramics in the ambient air was reported, in which the AgNbO₃ ultrafine powder with stable perovskite structure was synthesized by hydrothermal method instead of the conventional ball milling process, leading to a lower temperature of phase formation and thus smaller grain size. The resulting ceramics sintered at 940 °C displayed high breakdown strength (216 kV/cm) and a recoverable energy density of 3.26 J/cm³ with efficiency of 53.5 %. Also, the high thermal stability of recoverable energy density (with minimal variation of ≤20 %) and efficiency (≤ 10 %) over 30–150℃, enables AgNbO₃ ceramics achieved to be a promising candidate for energy storage applications.     

抗FGF-2纳米抗体抑制碱烧伤诱导大鼠角膜血管新生

目的：研究抗成纤维细胞生长因子（FGF-2）纳米抗体对碱烧伤诱导的大鼠角膜血管生成的治疗作用。方法：将SD大鼠分为：假手术组（Sham），模型组（Model，直径为3 mm的浸有1 mol/L NaOH溶液圆形滤纸贴于大鼠眼角膜中央处30 s，制备大鼠碱烧伤血管生成模型）和治疗组（Treatment，术后7天至21天用3 mg/mL的抗FGF-2纳米抗体溶液滴眼，每日3次，每次10 μL，共14天）。通过体视显微镜和CD31免疫组织化学染色计算大鼠角膜血管生成情况。实时荧光定量PCR、酶联免疫吸附测定和免疫组织化学染色3种方法检测抗血管内皮生长因子（VEGF）和FGF-2的mRNA和蛋白表达水平。结果：（1）血管：治疗组较模型组的面积显著减少，血管管腔较窄（P<0.05），在药物干预14天后，差异最为显著；（2）FGF-2的mRNA和蛋白表达水平：模型组与治疗组的结果相近（P>0.05）；（3）VEGF的mRNA和蛋白表达水平：治疗组显著高于模型组（P<0.05）。此外，假手术组的持续给药也使得VEGF表达显著增加（P<0.05）。 结论：抗FGF-2纳米抗体可抑制由碱烧伤诱导的角膜血管新生，但也使得正常大鼠角膜或病理大鼠角膜的VEGF表达水平代偿性升高。     

Additive Manufacturing of Stable Energy Storage Devices Using a Multinozzle Printing System

The development of the Internet of things has prompted an exponential increase in the demand for flexible, wearable devices, thereby posing new challenges to their integration and conformalization. Additive manufacturing facilitates the fabrication of complex parts via a single integrated process. Herein, the development of a multinozzle, multimaterial printing device is reported. This device accommodates the various characteristics of printing materials, ensures high-capacity printing, and can accommodate a wide range of material viscosities from 0 to 1000 Cp. Complete capacitors, inclusive of the current collector, electrode, and electrolyte, can be printed without repeated clamping to complete the preheating, printing, and sintering processes. This method addresses the poor stability issue associated with printed electrode materials. Furthermore, after the intercalation of LiFePO₄ with Na ions, X-ray photoelectron spectroscopy and X-ray diffraction results reveal that the Na ions permeate the interlayer structure of LiFePO₄, enhancing the ion migration channels by increasing the ion transmission rate. A current rate of 2.5 mAh ensures >2000 charge/discharge cycles, while retaining a charge/discharge efficiency of 96% and a discharge capacity of 91.3 mAh g⁻¹. This manufacturing process can provide conformal power modules for a diverse range of portable devices with various shapes, improving space utilization.     

A Biologically Muscle-Inspired Polyurethane with Super-Tough,Thermal Reparable and Self-Healing Capabilities for Stretchable Electronics

Polymeric elastomers play an increasingly important role in the development of stretchable electronics. A highly demanded elastic matrix is preferred to own not only excellent mechanical properties, but also additional features like high toughness and fast self-healing. Here, a polyurethane (DA-PU) is synthesized with donor and acceptor groups alternately distributed along the main chain to achieve both intra-chain and inter-chain donor-acceptor self-assembly, which endow the polyurethane with toughness, self-healing, and, more interestingly, thermal repair, like human muscle. In detail, DA-PU exhibits an amazing mechanical performance with elongation at break of 1900% and toughness of 175.9 MJ m⁻³. Moreover, it shows remarkable anti-fatigue and anti-stress relaxation properties as manifested by cyclic tensile and stress relaxation tests, respectively. Even in case of large strain deformation or long-time stretch, it can almost completely restore to original length by thermal repair at 60 °C in 60 s. The self-healing speed of DA-PU is gradually enhanced with the increasing temperature, and can be 1.0–6.15 µm min⁻¹ from 60 to 80 °C. At last, a stretchable and self-healable capacitive sensor is constructed and evaluated to prove that DA-PU matrix can ensure the stability of electronics even after critical deformation and cut off.     

一种基于实时几何测距的船桥主动防撞方法

本文提出一种基于实时几何测距的船桥主动防撞方法。该方法对船的改动量甚微,仅需维持多项距离矩阵,通过告警逻辑矩阵进行展示与告警,能起到很好的船桥防撞提示效果。     

Surface generation mechanism of ceramic matrix composite in ultrasonic assisted wire sawing

Ceramic matrix composites (CMC) are highly required in many fields of science and engineering. However, the CMC parts always have poor surface finish. This study attempts to improve cutting performance of CMC material by combing the advantages of ultrasonic assisted cutting and diamond wire sawing. Cutting force, surface roughness, machined edge and tool wear are analyzed based on experimental results. It shows that the oscillatory movement of tool edges provides positive effect on particle ejection and residual material reduction. Ductile chip formation can be achieved due to the small tip radius of grits. Obvious decrease in cutting force, surface roughness and tool wear are obtained. Moreover, burrs, fuzzing and fracture are reduced. Meanwhile, both the surface characteristics and shape accuracy are significantly improved. These results provide a valuable basis for application of ultrasonic assisted wire sawing and understanding of CMC cutting mechanisms.     

Different hydrothermal corrosion results between two sides of sodalime float glass and the possible corrosion mechanism

Sodalime float (SF) glass is widely used in our societies and industries. Hydrothermal corrosion method is one of the effective ways to prepare a superhydrophobic glass, but there is still lack of knowledge about hydrothermal corrosion behavior and mechanism of SF glass. We have hydrothermally treated SF glass at 180 °C for different time, and tried to reveal the aqueous corrosion process of SF glass. We have characterized the morphologies and chemical compositions of samples, and found that (1) the two sides of SF glass have different corrosion resistances, and (2) a multilayer structural coating with a nanoflake layer (Mg-rich gel layer), a nanowire layer (Ca-rich gel layer), and a porous layer (etched layer) is formed on the air-side of SF glass. Based on the experimental results, we have proposed an aqueous corrosion mechanism of SF glass. The insights of the hydrothermal corrosion behaviors and mechanism provide helpful guidelines to glass surface structural control and functionalization.     

Electrorheological response behavior of H2Ti2O5@MoS2@SiO2 core-shell nanoparticles

In this paper, a novel H₂Ti₂O₅@MoS₂@SiO₂ ternary composite material was prepared by a combination of dual hydrothermal method and controlled hydrolysis method, in which H₂Ti₂O₅ nanotubes are tightly combined with hierarchical molybdenum disulfide, and the unique structure of titanate nano whiskers, including the loosely bound alkali metal ions between the titanate layers with high dielectric constant and the large aspect ratio, which induce active response to the electric field. Flower-like molybdenum disulfide provides electrical conductivity, and silicon dioxide as a insulative coating layer can suppress excessive the electrical conductivity of the two-dimensional material. The morphological evolution was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results of showed that the sheet-shaped molybdenum disulfide coated with curved H₂Ti₂O₅ nanotubes showed a honeycomb structure with uniform size. Silicon oxide acts as a cladding layer to increase the thickness of the flakes. The existence of H₂Ti₂O₅, molybdenum disulfide and silicon dioxide is confirmed by X-ray powder diffractometer (XRD) and Fourier transform infrared spectroscopy (FT-IR). The prepared product was confirmed by XPS, BET test and electrorheological rheometer. Core/shell nanoparticles not only exert the active response characteristics of titanate nanoparticles and molybdenum disulfide to electric field, but also inherit the excellent characteristics of a core-shell structure produced by the interface polarization and the synergistic effect of the polar groups on the surface of the two-dimensional material further enhance the electrorheological effect.     

Tribological mechanism of micro-arc oxidation coatings prepared by different electrolyte systems in artificial seawater

The micro-arc oxidation (MAO) coatings were prepared in four different electrolyte systems, including mixed acid, phosphate, phosphate-aluminate and phosphate-silicate electrolytes. The friction and wear properties of MAO coatings in ambient air, seawater and four groups of saline solutions related to seawater were investigated. The results showed that the addition of silicate to phosphate could increase the density of the coating. The phosphate-aluminate ceramic layer exhibited the lowest wear rate in various environments. Additionally, the friction coefficient and wear rate of MAO coating in seawater were lower than those in ambient air, which was due to the boundary lubrication effect of seawater. Meanwhile, the presence of divalent metal salts in seawater made its lubricity better than other salt solutions.